PTZ Optics 20X-USB Manuel d'utilisateur

PTZ Optics 20X-USB User Manual V1.0 (English)

9 Main Unit 1. Audio LINE IN Interface 7. RS232 IN jack 2. Audio LINE OUT Interface 8. RS232 OUT jack 3. CVBS Interface

10 IR Remote Controller Explanation 0. Standby Button Press this button to enter standby mode. Press it again to enter normal mode.

11 Press [AUTO] adjust the focuses on the center of the object automatically. To adjust the focus manually, press the [MANUAL]

12 USE IR Remote Controller When the camera is working, you can use remote controller to perform panning, tilting, zooming and foc

13 3. Focus Control Focus Far: Press [FOCUS+] button (NOTE: Effective only in manual focus mode) Focus Near: Press [FOCUS-] button (

14 Press any of the numeric buttons 0-9 directly to recall stored preset positions and settings. Note: No action is executed if a re

15 RS-232 Interface Camera Windows DB-9 1.DTR 1.CD 2.DSR 2.RXD 3.TXD 3.TXD 4.GND

16 Serial Communication Control In default working mode, the camera is able to connect to a VISCA controller with RS232C serial interface. #

17 The camera can be controlled via RS485, Half-duplex mode, supports VISCA or Pelco-D or Pelco-P protocol, supports the following

18 VISCA Command List Part 1 Camera-Issued Messages Ack/Completion Message Command Function Command Packet Comments ACK/Comletion Messages ACK

1 Preface Thanks for using this USB3.0 HD Video Conferencing Camera. This manual introduces the function, installation and operation of the HD c

19 Command Not Executable z0 6y 41 FF (y: Execution command Socket No. Inquiry command: 0) Returned when a command canot be executed due to curr

20 Outdoor mode 8x 01 04 35 02 FF Outdoor mode OnePush mode 8x 01 04 35 03 FF One Push WB mode Manual 8x 01 04 35 05 FF Manual Control mode On

21 CAM_ExpComp On 8x 01 04 3E 02 FF Exposure Compensation On/Off Off 8x 01 04 3E 03 FF Reset 8x 01 04 0E 00 FF Exposure Compensation Amount Sett

22 CAM_RegisterValue - 8x 01 04 24 mn 0p 0q FF mm: Register No. (=00-7F) pp: Register Value (=00-7F) CAM_ColorGain Diret 8x 01 04 49 00 00 00

23 Flip-HV 8x 01 04 A4 03 FF CAM_SettingSave Save 8x 01 04 A5 10 FF Save Current Setting CAM_Iridix Direct 8x 01 04 A7 00 00 0p 0q FF pq: Iridix

24 y0 50 0A FF Shutter priority y0 50 0B FF Iris priority y0 50 0D FF Bright CAM_ShutterPosInq 8x 09 04 4A FF y0 50 00 00 0p 0q FF pq: Shutter

25 CAM_RegisterValueInq 8x 09 04 24 mm FF y0 50 0p 0p ff mm: Register No. (00 to FF) pp: Register Value (00 to FF) CAM_ColorGainInq 8x 09 04 49

26 CAM_TypeInq 8x 09 00 03 FF y0 50 01 FF C Type y0 50 02 FF M Type y0 50 03 FF S Type CAM_DateInq 8x 09 00 04 FF y0 50 0r ss uu uu vv ww 0D FF

27 Command Command packed Inquiry Packet Comments CAM_LensBlockInq 8x 09 7E 7E 00 FF y0 50 0u 0u 0u 0u 00 00 0v 0v 0v 0v 00 0w 00 FF uuuu: Zo

28 Pelco-D Protocol Command List Function Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Up 0xFF Address 0x00 0x08 Pan Speed Tilt Speed SUM Down 0xFF

2 Contents 1、 Note ································································································ 3 2、 Supplied Accessories

29 Pelco-P Protocol Command List Function Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Byte8 Up 0xA0 Address 0x00 0x08 Pan Speed Tilt Speed 0xAF XO

30 Menu Setting 1. MENU Press [MENU] button to display the main menu on the normal screen, using arrow button to move the cursor to the ite

31 Bright: Intensity control, Optional items: 00~17. (Effective only in Bright mode) Anti-Flicker Flicker: Anti-flicker. Optional items: Of

32 AWB sens: The white balance sensitivity, Optional items: Normal, High, Low. Style: Optional items: Style1, Style2, Style3. 4. IMAGE Move t

33 main menu and press [home] button, NOISE REDUCTION menu appears, as shown in the following figure. NR2D-Level: 2D noise reduction. O

34 Baudrate: Serial port baud rate. Optional items: 2400, 4800, 9600 8. RESTORE DEFAULT Move the cursor to the Restore Default item in t

35 Equipment Setup and internet connection 1. Operating Environment Operating System: Windows 2000/2003/XP/vista/7 Network Protocol: TCP/IP Cl

36 Picture 1.2 Connect by router /interchanger IP camera visited/ controlled by LAN 1 Setup IP address 1.1 Connect IP Camera to internet (or P

37 Click “config” then go to below:

38 Enter new IP in "IP" bar, subnet mask in "Mask" bar, Gateway,First DNS, MAC address,and click “Set”. Shown as abov

3 Note " Electric Safety Installation and operation must accord with electric safety standard. " Caution to transport Avoid stress,

39 2.2 Input login name and password, click "confirm", then pop up below window,language select button on the left bottom:

40 NOTE！ If user first time use this camera by internet (only for new user), must install a player software (VLC). Please go to http://4dx.pc6.c

41 2. Dynamic DNS visit camera 1.1 Camera accessed by dynamic DNS Set domain name to camera, setup the parameter, then dynamic DNS can access

42 1.2 Input URL address: rtsp://ip: port number/1 (Main stream); rtsp://ip: port number/2(sub stream)(When RTSP port number default value is

43 IP Camera parameter setup 1 Homepage introduction 1.1 Menu All pages include 2 menu bars: Real time monitoring: displaying video image Pa

44 1) PTZ direction control box: Up, down, left, right, home oblique button as above 2) Rate: Vertical speed can be chosen as 1 ~ 24, horizon

45 1 Media 1.1 Video Setup,please click "Video" 1) Video format Support 50HZ(PAL)and 60HZ(NTSC),and Dial priority three formats.

46 Main bit flow support 1920x1080,1280x720,minor bit flow support 640x360,320x180,the bigger resolution is, the clearer the image will be, more

47 1) Brightness Image bright 0~100, slider control, on the right shows the corresponding numerical. Default 43. 2) Saturation Saturation 0~1

48 Adjusted the wide-angle lens image distortion occurs, controllable range 0 ~ 100, right shows the corresponding numerical. Default 0. 7) Fli

4 Quick Start Step1. Please check connections are correct before starting Step2. Setting switches Set both of the switch1 and switch2 to &quo

49 5) Input VolL The volume of the left channel 6) Input VolR The volume of the right channel 7) Button Press "apply" button to

50 1) Lan Settings!Default the IP address is 192.168.100.88, The MAC address can be modified. 2) Port Settings!IP address identifies the netw

51 Network camera support RTSP protocol, use the VLC tools broadcast. 4) TCP Port!Support TCP protocol, default port: 5678. 5) Apply / Canc

52 Network Control 1. View from Web browser (better in IE) " To view from web browser, firstly need to check camera IP address. There are

53 Method 2: Open “upgrade_En.exe”, change IP and click “Set”

54 3. Once IP changed, need to restart the camera. 2 methods to restart as below: Method 1: Turn off and turn on manually to restart camera M

55 PTZ ON IP NETWORK This model currently supports various PTZ control methods, including RS232, RS485, IR remote control, HTTP CGI, and TCP p

56 DownRight 81 01 06 01 VV WW 02 02 FF Stop 81 01 06 01 VV WW 03 03 FF Home 81 01 06 04 FF Preset position Reset 81 01 04 3F 00 PP FF PP: Posi

57 http://[Camera IP]/cgi-bin/ptzctrl.cgi?ptzcmd&[action]&[position number] More descriptions: [Camera IP]: This camera IP address; [a

58 Maintenance and Troubleshooting Camera Maintains " If camera will not be used for a long time, please turn off the power swit

5 Step3. Setting of the system select switch The option of video format: VIDEO SYSTEM 0 - 8 - 1 - 9 - 2 1080i60 A - 3 108

59 3. Check IR address of the Remote Commander is set correctly. " Serial communication cannot control the camera 1. Check the camera wor

6 Features 1. Support USB3.0 transmission, the highest rate up to 5Gbps, ensure real-time lossless HD data transmission. 2. Support HD USB3.0,H

7 Product Specification Model 20X-USB Name PTZ Optics USB3.0 Type HD Color Video Camera Camera Video System 1080i/60,1080i/50, 1080p/30, 1080p/2

8 Horizontal Rotation Range ±170° Control Input/Output 1xRS-232 IN: 8pin Min DIN, Max Distance: 30m, Protocol: VISCA/ Pelco-D/Pelco-P Verti